U-line 75 Manual do Utilizador

RRRP.O. Box 245040Milwaukee, WI 53224-9540Phone 414.354.0300FAX 414.354.7905www.U-Line.comICE-MAKERS, COMBOS,REFRIGERATORS,75 BEV BEVERAGECENTER Prin

8User’s ManualELECTROCUTION HAZARD!Electrical Grounding Required. This applianceis equipped with a three prong (grounding)polarized plug for your prot

9NOTEKeep in mind that the door of the unit may be mounted oneither side of the cabinet (see REVERSING THE DOOR)except for the 75 BEV. All U-Line unit

10User’s ManualLEVELING THE UNITIt is important that these units, primarily the ice maker assembly and75 BEV are level. All 75 and 15 Series units are

114. Place the unit in position where it is to be installed. Re-check cabinet height and levelness (Figure 4) and adjust if necessary.Figure 3Figure

User’s ManualCONNECTING THE WATER SUPPLY - ICE MAKER MODELS ONLYInstall a 1/4" outside diameter copper water line (not supplied with unit) from t

131. Locate the compression fittingand ferrule packed in the unit.Slide the compression fitting andferrule over the 1/4" outsidediameter water s

14User’s ManualFigure 9NOTEOn BI-95 and BI-98 models, route the water supply linethrough the unit so it does not come into contact with anyinternal co

15NOTE After completing the installation, turn on the water andrecheck water connection for leaks. Apply additional tight-ening if needed. Do not use

4. Place the two hook-hinges (located on the rear bottom side of thegrille) on the front lip of the unit base. Swing the grille up into posi-tion, al

1795 AND 98 MODELS1. With a standard blade screwdriver (or 1/4" nutdriver), removethe screw needed to attach the grille (see Figure 13).2. Care

U-LINE CORPORATION LIMITED WARRANTYU-Line Corporation warrants each U-Line product to be free from defects in materials andworkmanship for a period of

18User’s ManualGLASS SHELF INSTALLATION(for models with Glass Shelves)1. Carefully remove the glass shelves from the packaging.Figure 152. Slide the

19BUILT-IN INSTALLATIONYour U-Line product is designed to be built-in or freestanding. Whenbuilt-in, they do not require additional air space for the

20User’s ManualCUSTOM DOOR PANEL INSERTNOTEThe SP18 and 75 BEV models are not designed to acceptcustom door panels. A custom door panel can be install

21Figure 184. Remove two small screwsholding door handle. Slightlyseparate door handle fromdoor (Figure 20).5. Pull handle up and off.UL131 Fi

22User’s ManualNOTEUse care not to bend light switch bracket (where installed),located on door bottom when installing door insert. Do notset door on b

23To add a final finish coat:1. Remove the top two racks. See WINE RACK REMOVAL/INSTALLATION.2. Remove screws securing wood trim to the two racks atta

24User’s ManualTo stain for a different wood color:1. Remove the top two racks. See WINE RACK REMOVAL/INSTALLATION.2. Remove screws securing wood trim

WINE RACK REMOVAL/INSTALLATIONTo remove the wine racks for cleaning or refinishing:Figure 211. Grasp the end of the wine rack, sliding it out and up.

REVERSING THE DOORDepending upon the location of the unit, it may be desirable to changethe side on which the door is mounted.NOTEOn Combo Models 29A

Figure 24Figure 25UL110UL11127Figure 26Figure 27UL113BUSHINGUL1126. Relocate plastic spacer/bushing on bottom of door to oppositeside, and place door

1INTRODUCTION Congratulations on your purchase of your U-Line product. A pioneer inthe field for more than 40 years, U-Line is the world’s number one

8. Remove pivot screw from top hinge, invert screw and reinstallpivot screw in top hinge (Figure 28).Figure 28HINGERIGHT SIDEDOOR SWINGLEFT SIDEDOOR

12. Adjust door to assure proper seal. Tighten upper hinge screwssecurely.13. Replace three plastic plugs removed in step 8 into holes on top ofunit.

8. Install bottom hinge on cabi-cabinet, opposite side, align-ing flat edge of hinge withouter edge of unit. Partiallytighten screws (Figure 32).9. R

REVERSING A STAINLESS STEEL DOORStainless Steel models are fieldreversible for left or right hand opening. The door opening is easilyreversed by movin

ALIGNING THE DOORFor proper door alignment:Figure 341. Loosen top and bottom hinge screws (Figure 34).2. Align door squarely with cabinet.3. Make s

Figure 35NOTEWhen inspecting door alignment, make sure the lightswitch bracket makes contact with the light switch plunger(Figure 35). Also, make sure

34User’s ManualINITIAL START-UP AND ADJUSTINGTHE TEMPERATURE CONTROLU-Line recommends the unit be allowed to run overnightand make ice on ice-maker mo

35Allow unit temperature to stabilize for 24 hours before use.4. Open the water supply valve in the main water source. As soon asthe ice maker mold r

Factors which affect the internal temperatures of the cabinet include:1. Temperature setting.2. Room temperature where used or installed.3. Number o

37NORMAL OPERATIONOn units with refrigerator sections, the unit has been designed toachieve a fresh food temperature of approximately 38°F. Units with

PLEASE RECORD YOUR MODEL’S INFORMATIONWhenever you call to request information or service, you will need toknow your model number and serial number. Y

38User’s ManualIf ice maker is not used regularly, the ice bucket should be emptied periodically to ensure fresh cubes.It is normal for cubes to appea

39MARINE USEMany U-Line models are designed to operate in a harsh marine environment. Special considerations include the following:• For best performa

40User’s ManualADJUSTING ICE CUBE SIZEOn models equipped with an ice maker, the cube size may be adjustedby changing the amount of water injected into

41CAUTIONUse only genuine U-Line replacement parts. U-Line icemaker parts are not the same as standard FSP Whirlpoolparts. Using non U-Line parts can

42User’s ManualLIGHT BULB REPLACEMENTFigure 41Light bulb replacement is simple.1. Remove the light housing cover by sliding the cover toward the tab,

43PROPER STORAGE and STOCKINGRECOMMENDATIONSYour Beverage Center will accommodate up to 16 bottles (750 MLsize) on the wine racks: up to eight bottles

44User’s ManualCLEANING & MAINTENANCEPeriodic cleaning and proper maintenance will ensure efficiency, topperformance, and long life. The maintenan

45Condenser Cleaning – Every Three MonthsDisconnect electric power to the unit before cleaning thecondenser or the solenoid valve.Figure 43Keep the fr

46User’s ManualDO NOT touch the condenser fins. The condenser fins areSHARP and can be easily damaged.4. Clean the condenser coil using a soft brush

47Figure 463. Use a tooth brush to clean sediment from the inlet screen (Figure 46). DO NOT remove the screen.4. Attach the hose connector to the so

TABLE OF CONTENTSINTRODUCTION...1SAFETY PRECAUTIONS ...

48User’s ManualSTORAGEIf the unit is to be stored or not used for extended periods:1. Remove all contents from the unit.2. Shut off water supply at

49TROUBLESHOOTINGBEFORE CALLING FOR SERVICEIf the unit appears to be malfunctioning, read through NORMAL OPER-ATION first. If the problem persists, ch

50User’s ManualProblem Possible Cause RemedyThe unit is not Airflow to front grille Airflow must not be cold enough (cont.) blocked obstructed to fro

51Problem Possible Cause RemedyNo ice Bin arm locked in Lower bin arm.upright positionNo water to unit. Turn on water or contactplumber.Not enough ic

52User’s ManualSPECIFICATIONSIce Production Cube Fresh FoodUnit TypeModelCapacity Storage (refrigerator)Freezer DefrostNumber(per day) Capacity Capaci

U-LINE CORPORATION LIMITED WARRANTYU-Line Corporation warrants each U-Line product to be free from defects in materials andworkmanship for a period of

RRRP.O. Box 245040Milwaukee, WI 53224-9540Phone 414.354.0300FAX 414.354.7905www.U-Line.comICE-MAKERS, COMBOS,REFRIGERATORS,75 BEV BEVERAGECENTER Prin

SAFETY PRECAUTIONSDo not attempt to install or operate your unit until you have read thesafety precautions in this manual. Safety items throughout thi

5GENERAL PRECAUTIONSRisk of child entrapment. Before you throw away your oldrefrigerator or freezer, take off the doors and leave shelvesin place so t

6User’s ManualGENERAL PRECAUTIONS (CONTINUED)CAUTION• Using a heater to speed up defrosting can damage theinner lining. DO NOT use any type of electri

7INSTALLATIONSITE PREPARATIONYour U-Line product is designed to be installed in a wall or under acounter or freestanding.NOTEThe 75 BEV must be ordere